Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateWhy Bellevue Homeowners Choose Ghost Controls Gate Repair
Bellevue Gate Repair provides independent Ghost Controls gate repair service in Bellevue, WA. We repair, service, and install Ghost Controls swing and slide operators, and because it’s one of nine gate brands we work on every week, we know the AR-1 and AXO control boards, the MMS slide operators, and the GhostCode and GhostKey accessories from the inside out. We are not affiliated with, authorized by, or endorsed by Ghost Controls – we’re an independent shop, and that’s exactly why we can be honest with you about repair versus replacement. Call (855) 683-9015 for a free estimate on your Ghost Controls system in Bellevue.
What makes our Ghost Controls work different
Most general handymen and garage-door companies won’t touch an automated gate, and the ones who will are guessing at your control board. A Ghost Controls operator isn’t a simple motor and a switch. It’s a receiver, a controller, a set of limit magnets, and a battery backup system that all have to agree with each other, and the failure modes are specific.
Our technicians have up to experience, and Ghost Controls is part of the regular rotation. We work on residential driveway systems in Bellevue, multi-family entrances, and commercial access points.
Why Trust Bellevue Gate Repair for Your Ghost Controls Gate Repair?
Because we see Ghost Controls systems regularly, we can usually tell you what’s wrong before we finish the first diagnostic pass. When a Bellevue homeowner calls about a gate that opens halfway and stops, or a keypad that worked fine last week and doesn’t now, those aren’t mysteries to us. They’re known symptoms of known components.
We use quality parts that fit Ghost Controls equipment. Where the manufacturer’s part is available, we use it. Where a wear item like a battery or a remote is backordered, we use a quality equivalent that performs the same job rather than leaving your gate down for weeks. We’ll tell you which we’re using and why.
Warranty-safe service matters too. We approach Ghost Controls equipment the way it’s designed to be serviced: we reseal enclosures properly, we use correct-spec batteries, and we don’t modify boards or bypass safety circuits to make a symptom go away. If your unit is still under a manufacturer’s warranty, we’ll be clear about what a repair involves so you can make an informed decision. We’re an independent service provider, not an authorized Ghost Controls dealer.
What you get is a specialist on-site, not a generalist guessing at your control board.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Common Ghost Controls Gate Repair Problems We Fix in Bellevue
These are the failures we see most often on Ghost Controls systems around Bellevue. They’re diagnosable, and each has a known fix.
- Control board corrosion and water intrusion on AR-1 and AXO models. The sealed enclosure is only as good as its gasket. After a wet Bellevue season, that gasket can fail, letting damp air and water in. The board corrodes, and the gate starts behaving erratically – opening when it shouldn’t, ignoring remotes, or not responding at all. It’s one of the most common Ghost Controls calls we get.
- Battery backup and solar charging faults. The controller stops accepting a charge, or the battery drains faster than it should. The gate works fine until the power goes out, and then it’s stuck open. On solar setups, a dirty panel or a failing charge controller is often the culprit. Battery backup deserves a check before the storm season, not after.
- Limit switch and magnet misalignment. The gate stops short of the post, reverses mid-travel, or never quite closes. On a swing gate, a shifted magnet or a worn limit switch changes what the controller thinks is the end of travel. On a slide gate, a magnet that’s drifted a fraction of an inch has the same effect.
- Remote and keypad pairing dropouts. After a board swap or a firmware reset, the receiver loses its stored codes. The remotes and the GhostCode keypad stop working, and reprogramming isn’t obvious without the manual. We pair them back and confirm every code is stored correctly.
- Motor strain and grinding. A gate that drags on its track or a hinge that’s stiff puts load on the motor that it wasn’t designed for. Over time the operator strains, the motor heats up, and the safety-reverse trips. In Bellevue, wet fir needles and moss packed into a slide-gate track channel are a recurring cause.
A typical Ghost Controls AR-1 swing gate call, step by step
Here’s how this kind of job usually goes. A Ghost Controls AR-1 swing gate stops responding to remotes and the keypad after a stretch of rain. The control board enclosure has moisture inside and the receiver LED is dark. A qualified technician would dry and inspect the board for corrosion, test the transformer and battery voltage, and usually replace the receiver module or board and reseal the enclosure gasket. If the board turns out to be clean, the same symptom often traces to a failed limit magnet or a remote that lost its code after a power surge.
Ghost Controls Parts & Our Repair-vs-Replace Approach
We use OEM Ghost Controls boards, receivers, and limit switches when they’re available, and high-quality aftermarket equivalents for wear items like batteries and remotes when OEM is backordered. We don’t claim to stock genuine Ghost Controls parts – we source what fits and what works.
Repair versus replace is a judgment call, and we’ll make it honestly. A board-level repair can be the right call if the rest of the unit is sound and the motor is healthy. If the enclosure has been letting water in for years, the motor is tired, and the boards keep failing, replacing the operator is often the better long-term value. We’ll tell you which we think applies and why, and the price is quoted and agreed before any work starts.
If your Ghost Controls gate is acting up, call (855) 683-9015 for a free estimate.
Our Ghost Controls Service Process – Step by Step
- 1
Diagnosis. We test the transformer and battery voltage, inspect the control board and enclosure for moisture and corrosion, check the limit magnets and switches, and confirm the receiver is holding its stored codes. On a Ghost Controls AXO dual gate, we test each side separately to isolate whether the fault is a board, a limit, or a single motor.
- 2
Repair or install. We replace what’s failed with parts that fit Ghost Controls equipment, reseal the enclosure gasket properly, and correct any track, hinge, or alignment issues putting load on the motor. For a new install, we mount the operator, set the limits, and wire the accessories.
- 3
Test. We cycle the gate through full open and full close, verify the safety-reverse, test the battery backup by cutting power, and pair every remote, keypad, and accessory back to the receiver.
- 4
Warranty and handoff. We explain what failed and why, what we replaced, and what to watch for. We’ll be clear about how any remaining manufacturer warranty on your unit is affected by the work.
See the difference
Before
After
Before
After
Before
AfterGhost Controls Products We Service & Install in Bellevue
Ghost Controls makes swing and slide gate operators for residential driveways, and we service and install across that range. On the swing side, the AR-1 single-swing opener and the AXO dual-swing opener – including the case where one side of a dual gate stops moving while the other works. On the slide side, the MMS-1 and MMS-2 operators. We also service and install the GhostCode keypad and GhostKey accessories, handle remote and keypad pairing, and work on battery backup and solar charging setups. If your system is behaving oddly, we’ll diagnose it in a single visit.
We Also Service These Brands
Ghost Controls is one of nine gate and operator brands we work on. We’re equally at home with LiftMaster, Mighty Mule, and DoorKing systems, along with FAAC, BFT, Linear, Viking, and Elite. That range means we diagnose the actual problem instead of defaulting to whatever brand one shop happens to know.
FAQs – Ghost Controls Gate Repair Service in Bellevue
No. We are an independent Ghost Controls service provider, not an authorized dealer, and we’re not affiliated with, endorsed by, or sponsored by Ghost Controls. We repair, service, and install their equipment as independent technicians. Call (855) 683-9015 for a free estimate.
Yes. We use OEM Ghost Controls boards, receivers, and limit switches when they’re available, and quality aftermarket equivalents for wear items like batteries and remotes when OEM is backordered. We don’t claim to stock genuine Ghost Controls parts – we source what fits and performs correctly. Call (855) 683-9015 to talk through your repair.
Most Ghost Controls repairs we handle are same-day or next-visit jobs, depending on whether a board or motor needs to be sourced. A board swap and gasket reseal is usually a single visit. A dual AXO where one side needs a new motor can take a bit longer if the part has to be ordered. We’ll give you a clear timeline before we start.
We cover the AR-1 single-swing opener, the AXO dual-swing opener, the MMS-1 and MMS-2 slide operators, and the GhostCode keypad and GhostKey accessories. We also handle battery backup and solar charging setups, remote and keypad pairing, and new installations. Call (855) 683-9015 to confirm your setup.
Not if the service is done correctly. We use correct-spec parts, reseal enclosures properly, and don’t modify boards or bypass safety circuits – the kinds of work that can cause warranty problems. We’ll be upfront about how any remaining manufacturer warranty on your unit is affected. When in doubt, ask Ghost Controls directly about your coverage.
Pricing is set per job by a written estimate after we’ve diagnosed the fault, because a board swap, a battery backup fix, and a motor replacement are different jobs. The estimate is free, and the price is quoted and agreed before any work starts. Call (855) 683-9015 for an exact quote.
Most often it’s the limit switch or magnet, not the board. A gate that stops at the same point every time is usually telling you the controller thinks it’s reached the end of travel – a shifted magnet or a worn limit switch will do that. A board fault tends to be more erratic. We test both in a single visit. Call (855) 683-9015 for a free estimate.
Because the receiver lost its stored code, not because the battery is bad. This happens after a power surge or a board reset, and the remote or keypad needs to be re-paired. Reprogramming isn’t obvious without the manual. We pair them back and confirm every code is stored correctly. Call (855) 683-9015 if you’d rather have it done for you.
Yes, in most cases. A dual AXO has two operators and often a single control board, so one side stopping while the other works usually points to a single motor, a limit, or a wiring fault on that side rather than a dead board. We test each side separately to isolate it. Call (855) 683-9015 for a free estimate.
Yes, Ghost Controls makes solar-compatible operators. In Bellevue, what usually fails on a solar setup is the charge side, not the operator: a dirty or shaded panel that stops charging, a failing charge controller, or a battery that’s aged out and no longer holds a charge through a wet winter. We test the whole charge path. Call (855) 683-9015 to have yours checked.
Start with water in the enclosure and a stuck or misaligned limit. Random opening is often a control board that’s taken on moisture, or a limit switch that’s triggering a false end-of-travel. It can also be a receiver picking up a stray signal. We test the board, the enclosure seal, and the limits in one visit. Call (855) 683-9015 for a free estimate.
Book Your Ghost Controls Service in Bellevue, WA
Whether your Ghost Controls AR-1, AXO, or MMS operator needs a repair, a battery backup check, or a new keypad install, we’ll get a specialist on-site. Call (855) 683-9015 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. The price is quoted and agreed before any work starts.
Written by the team at Bellevue Gate Repair.