Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Bellevue Homeowners
When an automated gate stops opening, closes on its own, or grinds to a halt halfway down the track, the fix usually isn’t the mystery it feels like. Most failures trace back to a handful of known culprits: a worn roller, a misaligned track, a control board that’s lost its programming, or a safety loop detector that’s gone bad. Our technicians have up to experience diagnosing exactly these problems, and we work on gate systems only, never as a side job between other trades. That focus is why a property manager in Bridle Trails or a homeowner off Cougar Mountain can call us and get a straight answer instead of a guess. We offer same-day service on many repairs, and we answer 24/7 at (855) 683-9015 so you can reach us when the gate fails. We quote and agree on the price before any work starts.

Driveway Gate Repair
Driveway Gate Repair covers the swing or slide gate that guards your driveway, and it’s what we do when that gate stops responding, drags, or won’t latch shut. It’s the right call when the gate moves but won’t fully close, when the operator hums without moving the leaf, or when a manual gate has started to sag and catch on the ground. We diagnose the mechanical structure and the electrical components in a single visit, so you’re not booking two different trades for one problem. Bellevue’s wet winters work on gate hardware, and a gate that was fine in October often shows hinge wear and frame swelling by February. Typical driveway gate repair ranges from $180 to $450 depending on the failure, and a written estimate sets the final price before we begin.
Diagnosing the Operator and Structure Together
An operator that won’t move is sometimes a control problem and sometimes a mechanical bind the motor is fighting. We test both sides in one visit so we’re not replacing a control board when the real fault is a seized roller. That separation is where most wasted money goes on driveway gate calls.
Sagging and Out-of-Square Leaves
Heavy gate leaves settle over time, especially on posts that take a lot of ground movement. A leaf that’s dropped a quarter inch can throw off the latch and the limit switches at the same time. We correct the alignment before touching the operator settings.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Welding
Gate Welding is the structural repair that restores a cracked weld, a broken hinge mount, or a failed frame joint on a steel or iron gate. You need it when the gate wobbles, when a hinge has torn away from the post, or when you can see a hairline crack at a corner joint that’s only going to spread. We weld on-site where the gate allows it, matching the repair to the existing frame so the gate keeps its shape and swing. It’s not a job for a generalist with a hobby welder; the heat and alignment have to be right or the gate warps and you’re back to square one. Gate welding typically runs $150 to $400 depending on access and how much frame work is involved, quoted and agreed before any work starts.
On-Site Versus Shop Repair
Most weld repairs happen on the gate itself, which saves you the cost and hassle of pulling a heavy leaf off its hinges. When a post or frame section is too compromised for on-site work, we’ll tell you straight and price the alternative. Either way the estimate is written before we start.
Matching the Existing Frame
A weld that doesn’t follow the original joint line shows and can flex again. We line up the repair to the existing frame geometry so the gate stays true and the hinge geometry stays put. The goal is a repair you can’t pick out of the gate.
Commercial Gate Repair
Commercial Gate Repair handles the automated gates that control access at apartment complexes, office parks, and gated communities, and it’s the work we take most seriously because a stuck gate means backed-up cars and a real access problem. You need it when an entry gate fails during peak hours, when the access control or intercom stops releasing the gate, or when a loop detector keeps the arm down. We work on the operator, the control board, the safety edges, and the access hardware as one system instead of treating them as separate trades. Property managers around Bellevue know a gate down at 8am is a line of tenants by 8:15. Commercial gate repair generally ranges from $250 to $900 depending on the system and the fault, and the free estimate lays out exactly what’s included before any work begins. For automation-specific faults, see our Bellevue Gate Repair main page.
Access Control and Intercom Integration
When the gate won’t release from the keypad or intercom, the fault is often in the signal path, not the gate motor itself. We trace it from the control board out to the reader or phone entry system. That keeps the repair focused on the actual failure instead of swapping parts.
Loop Detectors and Safety Edges
A safety loop that’s failed will either hold a gate open or refuse to let it close, and both create a safety problem. We test loop sensitivity and the reversing edges as part of every commercial visit. These are the components that protect people, so they get checked, not skipped.
Iron Gate Repair
Iron Gate Repair addresses the structural and finish failures that show up on cast and forged iron gates, from cracked joints to hinges that have worked loose over years of use. It’s needed when an iron gate has started to rack out of square, when a hinge pin has worn and the leaf drops, or when rust has eaten into a joint and weakened it. We repair the iron work itself and correct the alignment so the gate swings clean again. Iron holds up to weather but not to neglect, and a hairline crack at a corner is easier and cheaper to catch early than after it opens up. Iron gate repair typically falls in the $200 to $500 range depending on the structural work, and the written estimate is agreed before we begin.
Rust and Joint Integrity
Rust on the surface is cosmetic, but rust inside a welded joint is a structural concern. We probe the compromised areas and repair what’s actually weakened rather than patching over it. That tells you honestly how much life is left in the frame.
Hinge and Pivot Wear
Iron gate hinges take a lot of load and work loose as the years add up. When a hinge pin wears, the whole leaf shifts and starts binding on the latch or the ground. We rebuild the hinge points and re-hang the leaf true.
Sliding Gate Repair
Sliding Gate Repair fixes the gates that run along a track instead of swinging, and it covers everything from a leaf that’s jumped the track to a rack-and-pinion drive that’s slipping. You need it when the gate drags, stops mid-travel, grinds going one direction, or comes off the track entirely. A sliding gate off its track is a safety hazard because that much weight can crush or pin, so we treat it as a priority repair. We check the track, the rollers, the drive gear, and the operator limit settings together, since a track that’s shifted will throw off every other adjustment. Sliding gate repair usually runs $200 to $550 depending on the drive system and track condition, with the written estimate agreed before any work starts.
Track and Roller Alignment
The track is the foundation of any sliding gate, and when it shifts or settles, everything downstream misbehaves. We level and realign the track and replace worn rollers before tuning the operator. A gate that travels without resistance runs cooler and lasts longer.
Rack-and-Pinion Drive Faults
The operator’s rack and pinion is what actually walks the gate along its track, and a stripped tooth or loose rack shows up as a slip or a skip. We inspect the rack along its full length and set the drive tension correctly. That stops the grinding before it eats more teeth.
Wrought Iron Gate Repair
Wrought Iron Gate Repair covers the decorative iron gates with detail work, scroll patterns, and ornamental joints, where the challenge is repairing structure without wrecking the look. It’s the right service when a scrolled section has bent, when a finial or picket has broken loose, or when a decorative weld has failed and the gate sags on that side. We straighten and re-weld the ornamental sections to match the original design, then prime and finish the repair area so it blends in. A wrought iron gate is often the first thing a visitor sees, so a repair that looks patched is a repair half done. Wrought iron gate repair typically ranges from $180 to $450 depending on the detail work, quoted and agreed before any work begins.
Straightening Ornamental Sections
Bent scrollwork needs controlled heat and pressure to straighten without cracking the iron. We work the section back to its original line rather than cutting it out and replacing it. When a section is too far gone, we’ll say so and price the alternative.
Finish Repair After Welding
A weld exposes bare iron that will rust if it isn’t sealed, so the finish after the repair matters as much as the weld itself. We prime and finish the repaired area to protect it. That keeps the repair invisible from the street.
Metal Gate Repair
Metal Gate Repair is the catch-all for steel and aluminum gates, covering the frame straightening, hardware replacement, and structural adjustments that keep a metal gate moving and latching correctly. It’s needed when a metal gate has been struck, has bent frame tubing, has a hinge pulling out, or has started to bind because the frame is out of square. We assess whether the frame can be straightened or whether a section needs replacing, then do the work on-site in most cases. Metal gates are forgiving but not indestructible, and a small bend left alone will fatigue the welds around it over time. Metal gate repair falls around $150 to $400 depending on the damage and access, and the written estimate is agreed before we start.

Frame Straightening
Bent frame tubing can usually be brought back into line rather than replaced, which saves the gate’s original look. We measure the frame and work it back to square so the gate swings and latches properly. If a bend has fatigued the metal too far, we’ll tell you honestly.
Hardware Replacement
Hinges, latches, and stops are the parts that fail first on any metal gate, and replacing them is often the whole repair. We match the hardware to the gate’s weight and swing so the new parts last. That stops the same failure from returning next season.
Wood Gate Repair
Wood Gate Repair handles the gates built from cedar, redwood, and treated lumber, where the ongoing battle is moisture and the way Bellevue’s damp air swells and shrinks the boards throughout the year. It’s the service you need when a wood gate has started to sag, when a hinge has pulled loose from swollen wood, or when the frame has rotted at the ground contact point. We repair the joinery, re-hang the leaf, and seal the areas that take the most weather so the fix holds. Wood moves constantly in this climate, and a gate that binds in spring often frees up in summer, so the repair has to account for that movement. Wood gate repair typically runs $150 to $400 depending on the rot and structure involved, with the written estimate agreed before any work starts.
Moisture and Board Movement
Boards swell in the wet months and shrink back in the dry ones, and a gate framed too tight will bind or crack. We leave the right gaps at the joints and re-set the leaf so it stays clear through the seasonal swing. That’s the difference between a repair that lasts one year and one that lasts several.
Rot at the Ground Contact
The bottom rail and the ground-contact frame are where wood gates rot first, because that’s where moisture sits longest. We probe for soft wood and replace only the compromised section where possible. Treating the exposed wood afterward protects what’s left.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We work on LiftMaster operators regularly and know where the control boards and drive components tend to wear. We also service FAAC systems and are familiar with the specific ways their operators handle weight and travel limits. When a stone or iron gate needs more than an off-the-shelf operator can deliver, that FAAC experience matters because the operator has to match the gate. Whether the fault is electrical or mechanical, we diagnose the actual problem rather than defaulting to replacement.
If your gate runs a Mighty Mule operator, we service those too and understand the control and limit settings that trip most often. We’re also experienced with Elite gate operators and how their control logic responds to loop and safety-edge inputs. We work across a wide roster of gate brands, which means the unfamiliar system that makes other shops want to swap out parts is one we can usually diagnose. Whether you have a LiftMaster, a Mighty Mule, or any other make, we can help. See our gate repair service for the full picture of what we handle.
Signs You Need a Pro Right Now
- The gate won’t open or close fully. A gate that stops short is usually hitting a limit switch or a bind in the track, and forcing it can damage the operator. Get it looked at before the fault spreads.
- The operator hums or grinds without moving the gate. That sound is often a drive or gear failure, not a dead motor. Continuing to trigger it wears the parts further, so it’s worth a call.
- The gate reverses on its own or closes on a vehicle. A reversing gate that misfires is a safety problem with the loop detector or safety edge. This is the one to call about right away.
- The leaf has dropped, sagged, or come off its track. A heavy gate off its track can crush or pin, so don’t try to lift it back yourself. Stop using it and get a specialist on-site.
- A hinge or weld has cracked and the gate wobbles. A cracked weld only grows under the gate’s own weight. Catching it early keeps the repair small.
Our Process, Step by Step
- 1
We take your call and ask the right questions. We’ll ask what the gate is doing, what brand and type it is, and whether it’s manual or automated. That tells us what tools and parts to bring, so the first visit has a good chance of solving it.
- 2
We diagnose on-site, structure and electronics together. We test the mechanical side and the electrical side in one visit, using meter readings and control diagnostics rather than guesswork. That’s how we separate a control fault from a mechanical bind.
- 3
We give you a written estimate before touching anything. The estimate lays out the diagnosis and the repair, with a clear price range for each part of the job. Nothing gets approved until you agree to it.
- 4
We do the repair and test the whole system. After the fix, we run the gate through its full cycle and check the safety edges and loop. A repair isn’t done until the gate works as a complete system, not just in the one spot we fixed.
- 5
We walk you through what we found. You’ll hear plainly what failed and what to watch for, including wear points that are fine now but worth monitoring. That’s how a repair stays fixed.
How Much Does Gate Repair Cost in Bellevue?
Gate repair in Bellevue typically runs between $150 and $900 depending on the type of gate and the failure involved. A basic driveway gate repair usually falls in the $180 to $450 range, while commercial gate work with access control can reach $550 to $900. Sliding gate repairs run $200 to $550, wrought iron and iron work sit around $180 to $500, and wood gate repairs are generally $150 to $400. These are typical estimates, and the written estimate sets the final price before any work begins.
Several things move the price: the gate’s weight and material, whether the fault is mechanical or in the operator or control board, and how easy the worksite is to reach. A gate with a loop detector and intercom has more that can fail than a simple manual gate, and the diagnosis takes longer. Brand matters less than condition, though an unfamiliar operator can add diagnostic time.
To avoid overpaying, get a diagnosis that covers both the mechanical and electrical sides before anyone starts replacing parts. A shop that guesses at a control board when the real fault is a seized roller will charge for both. Ask for the written estimate and read what’s included: diagnosis, parts, labor, and a post-repair test of the safety components. Our free estimate lays all of that out before you commit, and we answer 24/7 at (855) 683-9015. Call (855) 683-9015 for an exact quote; estimates are free.
Our Service Area Near Bellevue
We work across Bellevue and the surrounding Eastside, including Mercer Island, Newcastle, Sammamish, Redmond, Issaquah, Kirkland, Bryn Mawr-Skyway, Union Hill-Novelty Hill, and East Renton Highlands. Same-day service is available for many repairs across this area, with fast dispatch from 7am to 7pm, Sunday through Friday. If your gate is over on Mercer Island, our gate repair page covers that area, and for Newcastle you’ll find the details on our gate repair page. Call (855) 683-9015 and we’ll confirm the next opening for your address.
Serving Bellevue, WA – Our Local Coverage Area
We serve Bellevue and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Bellevue
Gate repair is the diagnosis and fixing of a gate that has stopped working correctly, whether the problem is mechanical, electrical, or both. It covers the gate’s structure (frame, hinges, track, rollers, welds) and its automation (operator, control board, safety edges, loop detectors, access hardware). A full gate repair looks at both sides, because an operator fault and a bent frame often show the same symptom. We work on manual, electric, and automated gates for homes, HOAs, and commercial properties.
Most gate repairs take one to three hours on-site once the diagnosis is done. A simple hinge or latch fix might take under an hour, while a track realignment or operator reprogramming takes longer. If a part has to be ordered, the repair may need a follow-up visit, and we’ll tell you that before you commit. The estimate lays out the expected time so there are no surprises.
Gate repair in Bellevue typically ranges from $150 to $900 depending on the gate type and the fault. Driveway and metal gate repairs usually fall around $150 to $450, sliding gate work runs $200 to $550, and commercial gate repairs with access control can reach $250 to $900. These are typical estimates, and the written estimate sets the final price before any work starts. Call (855) 683-9015 for an exact quote; estimates are free.
Yes, we work on LiftMaster and Mighty Mule operators, along with FAAC and Elite systems and a range of other gate brands. Our technicians are familiar with the control boards, limit settings, and drive components on these systems. That range means an unfamiliar operator doesn’t send us straight to replacement. We diagnose the actual fault first.
Yes, same-day service is available for many gate repairs in Bellevue. We answer 24/7 at (855) 683-9015, with fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. We’re closed Saturday. The written estimate is still agreed before any work begins.
Warranty terms depend on the specific repair and the parts involved, and we’ll spell them out in the written estimate. We stand behind the work we do and will return if something that was repaired fails. Ask us about the warranty for your specific repair when we’re on-site. It’s part of the estimate, not an afterthought.
Make sure we can reach the gate and that there’s room to test its full cycle. If the gate is automated, have any remote, keypad, or access codes ready so we can test the release. Tell us what the gate is doing and when it started, and note any sounds, smells, or partial movement. That information speeds up the diagnosis and keeps the visit short.
Schedule Your Gate Repair Service in Bellevue Today
A gate that won’t open, won’t close, or closes when it shouldn’t is a problem with a known fix. Our technicians have up to experience, and gates are all we work on. Call (855) 683-9015 for a free, no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. We’ll diagnose the real fault, agree on the price in writing, and get your gate working again.
Written by the team at Bellevue Gate Repair.