Gate Installation Cost in Bellevue - Honest Price Ranges, Free Written Quote

Typical price ranges for the work, then a free on-site estimate and a written quote for your driveway. Site prep, power runs and safety gear priced in, not added later.

✓ Licensed & Insured ✓ Written quotes ✓ Free estimates
Call (855) 683-9015

Call to schedule your free estimate

Work is performed by our local vetted partner.

🛡 Licensed & Insured 📝 Written Fixed-Price Quotes 💲 Upfront Pricing · Free Estimates
How Much Does Gate Installation Cost in Bellevue, WA? (2026 Price Guide) | Bellevue Gate Repair
Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate
Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
Questions about your gate repair?Free estimate, price agreed before work starts
Call (855) 683-9015

How Much Does Gate Installation Cost in Bellevue?

Gate installation in Bellevue typically costs $2,800 to $6,500 for a single residential swing gate with an operator, and $6,000 to $16,000 or more for wide driveway or commercial slide gates with automation, safety loops and intercom wiring. A basic manual gate without power lands lower at roughly $1,200 to $3,200. Those ranges assume a straightforward install with a reasonably level driveway; difficult footing, slope or utility conflicts push the number up fast, and a written on-site estimate is what actually sets your price.

We’re a gate-only specialist, which matters on a pricing question. A general handyman quotes the gate and then figures out the wiring as he goes. We quote the gate, the operator, the power and the safety devices as one job because that’s the only way the number holds. Our technicians have up to experience, we work on nine operator brands across residential, multi-family and commercial systems, and we can diagnose the mechanical structure and the automation side in a single visit.

Key Takeaways

  • Residential swing gate with an operator: typically $2,800-$6,500 installed.
  • Driveway slide gate with automation: typically $6,000-$16,000+, depending on width and material.
  • Manual pedestrian gate: roughly $1,200-$3,200.
  • The operator and the electrical work are usually the largest single line items, not the gate itself.
  • Every Bellevue install needs a site visit before anyone can quote honestly. Estimates are free.

Gate Installation Cost Breakdown (2026)

Here’s how a gate installation in Bellevue splits across the pieces. These are typical 2026 ranges for the local market, not quotes. Material choice and driveway conditions move the total more than anything else.

Line item Typical range What drives the number
Gate panel and frame (single swing, metal) $900-$2,400 Width, material gauge, ornamental detail, powder-coat finish
Gate panel and frame (slide, driveway width) $2,200-$5,500 Cantilever vs. track, length, weight, material
Posts, footings and hardware $400-$1,400 Soil, slope, footing depth, hinge and latch quality
Operator (swing or slide, brand varies) $700-$2,600 Brand, gate weight, duty cycle, residential vs. commercial grade
Electrical run to the gate $600-$2,800 Distance from the panel, trenching, whether power already exists
Safety devices (photo eyes, loop detector) $250-$900 Number of loops, layout of the driveway
Access control (keypad, intercom, remote) $200-$1,500 Single keypad up to multi-unit intercom for HOAs
Removal of an existing gate $150-$600 Concrete set posts, weight, disposal

The pattern to notice: a gate that looks expensive on paper is often the operator and the electrical work. An operator on a heavy driveway gate runs considerably more than one on a light pedestrian gate, and a gate 90 feet from the house needs a longer electrical run than one 20 feet away. On sloped lots around Cougar Mountain or in the West Bellevue neighborhoods where driveways climb, the footings and the electrical layout are usually where the budget surprises people.

We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule systems regularly, so we can usually match an operator to the gate you actually want rather than the one an installer happens to stock. If you’re still deciding between fixing what you have and starting fresh, our Bellevue gate repair work often settles that question cheaper than a replacement quote.

Want to talk it through?Free estimate, price agreed before work starts
Call (855) 683-9015

What Affects Gate Installation Pricing in Bellevue

Six things move a Bellevue gate quote up or down. None of them are guesswork once we’ve stood on the property.

  • Gate type and width. A pedestrian swing gate and a two-car slide gate are different projects with different hardware, different operators and different footing loads. Width drives every line.
  • Automation vs. manual. Adding an operator to a manual gate roughly doubles the job. Automated gate installation involves control boards, safety devices and power, which is exactly the work general handymen turn down.
  • Soil and slope. Bellevue lots are frequently sloped and sometimes sit on fill or glacial till. Posts need proper footing depth to hold a heavy gate, and a slope may mean digging deeper or engineering a different gate design.
  • Distance to power. Trenching a new electrical run from the house or panel is billed by length. Existing power at the gate line saves real money.
  • Material. Aluminum, steel, wood and composite each land at different price points, and finishes like powder coating add to the panel cost. Wood also needs more upkeep in western Washington’s wet climate.
  • Access control and property type. A single remote is a small line item. An HOA or multi-family property with call boxes, intercoms, keypads and vehicle loop detectors is a much larger control system, and we install and wire those for commercial and multi-family clients in Bellevue.

One local factor that deserves its own note: the wet season. Water drains off driveways and pools at the gate line on a lot of Bellevue properties. If the operator sits in that runoff, the control board is the first thing to fail. When we install, we look at drainage before we look at hardware, because the cheapest install is the one that doesn’t need a repair call two winters running.

How to Save on Gate Installation

Most of the savings on gate installation come before anyone digs a hole. Here’s where the money actually is.

  • Get the on-site estimate, not a phone number. Gate pricing depends on slope, footing and power run, none of which a phone quote can see. A written estimate is the only number worth comparing, and ours is free.
  • Decide whether you need automation. If your driveway gate doesn’t need an operator, don’t buy one. A manual gate with good hardware serves a lot of Bellevue properties well.
  • Keep the gate close to power. If power already reaches the gate line, say so at the estimate. It’s one of the biggest savings available.
  • Match the operator to the gate. Overpowering a light gate wastes money; underpowering a heavy one means replacement in a couple of years. Getting the pairing right the first time is the real saving.
  • Reuse good structure where it holds. If an existing gate is sound and only the operator has failed, we’ll tell you that. Brand-agnostic diagnostics mean we fix the actual problem rather than defaulting to a whole new system.

For a clear number on your property, call (855) 683-9015. Estimates are free, and we’ll price the gate, operator and electrical as one job so nothing shows up later.

Need a price for your gate repair?Free estimate, price agreed before work starts
Call (855) 683-9015

FAQs – Gate Installation Cost

How much does a gate installation cost in Bellevue?

A residential swing gate with an operator typically runs $2,800-$6,500 installed in Bellevue, and a wide driveway slide gate with automation runs $6,000-$16,000 or more. Manual gates land around $1,200-$3,200. The exact figure depends on gate width, material, slope and how far the gate is from power. Call (855) 683-9015 for a free on-site estimate.

Is it cheaper to repair my existing gate or install a new one?

Repair usually costs less when the structure is sound: a repair is typically a few hundred dollars versus a few thousand for a new install. Replacement makes sense when the posts, frame or hardware are failing, or when the gate is too light or too heavy for the operator you need. We look at both before you spend anything. Call (855) 683-9015 and we’ll tell you which is the honest answer for your gate.

Does the operator or the gate itself cost more?

The operator and the electrical work together usually cost more than the gate panel, typically $1,300-$5,400 combined versus $900-$5,500 for the panel. The power run and safety devices are what separate a manual gate quote from a full automated install. Call (855) 683-9015 for a breakdown on your property.

Can I put an operator on an existing gate?

Often yes, and automating an existing gate typically costs $1,500-$4,500, which is less than a new gate plus an operator. The gate has to be structurally sound and safely balanced; a heavy or sagging gate won’t work with a new operator no matter how good the operator is. We check the structure before we recommend it. Call (855) 683-9015 to have us look.

How long does gate installation take?

A single residential gate with an existing power supply typically takes one to two days. A slide gate with trenching, loops and new electrical usually runs two to four days, and HOA or commercial systems take longer depending on access control. Call (855) 683-9015 and we’ll give you a realistic timeline with the estimate.

Do I need a permit for a gate installation in Bellevue?

That depends on the work. Electrical connections and structural posts often require permits, and the rules vary by the city and by whether the property is residential or commercial. Ask the city’s building department what your job needs before work starts, and ask us to include the electrical scope in writing so it’s clear what’s covered. Call (855) 683-9015 with questions about the gate side.

What if my gate stops working at night or on a weekend?

We answer 24/7. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (855) 683-9015.

Do you work on HOA and commercial gates?

Yes. We install, repair and automate residential, multi-family and commercial gates, including HOA entry gates with call boxes, intercoms and vehicle loop detectors. Those systems involve more control wiring, so the estimate includes the access control scope in writing. Call (855) 683-9015 for an HOA or commercial assessment.

Get Your Gate Installation Estimate

Gate installation is not a job for a generalist guessing at a control board. Whether you’re automating an HOA entry gate, replacing a failing driveway gate, or adding a pedestrian gate to a side yard, we’re a gate-only specialist and we’ll quote the whole job clearly. Call (855) 683-9015 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.

Pricing reflects the Bellevue market as of 2026. Bellevue Gate Repair offers free estimates – call (855) 683-9015.

Written by the team at Bellevue Gate Repair.

What Our Customers Say

★★★★★ 4.9 from 8+ reviews

"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."

- Allison Ziegler

"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."

- Jason Norris

"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."

- Paul Reed
Need Gate Repair help in Bellevue? Licensed & insured · 30-60 min response · free estimates
Call (855) 683-9015

Request a Free Estimate

Tell us what's going on in Bellevue. We'll get back to you fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - We Answer 24/7
Local Service Coverage
Call Now - We Answer 24/7