Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Bellevue?
Gate parts and welding in Bellevue typically run $150 to $450 for a repair involving a weld, a hinge, a roller or a latch, while a replacement operator board or motor assembly commonly lands between $300 and $900 installed. A full weld-and-hang job on a bent or sagging gate frame usually falls between $400 and $1,200, and a finished replacement of a heavy slide or swing leaf runs from $1,800 to $6,500. Every one of those figures is an estimate. The written estimate you get after we look at the gate sets the final price.
Our technicians have up to experience with gate structure and gate electronics, and that matters on this kind of work because a wobbling gate is rarely just a welding problem or just a parts problem. It’s usually both, and we diagnose the mechanical side and the automation side on the same visit. Call (855) 683-9015 for a free estimate.
Key Takeaways
- Small structural repairs (welds, brackets, hinges, latches, rollers) usually land in the $150 to $450 range.
- Operator and control components (boards, motors, loop detectors, receivers) run $300 to $900 installed for most residential and light commercial systems.
- Heavy slide gates and welded frame rebuilds cost more because of steel, finish work and the labor to re-hang a leaf safely.
- Gate parts cost what they cost – the controllable variable is how much diagnostic time you pay for.
- Free estimates, upfront pricing, and a written price before any work starts.
Gate Parts & Welding Cost Breakdown (2026)
The table below shows what we typically see in the Bellevue market for parts and welding work. These are estimated ranges, not quotes. The gate’s weight, material, brand, and condition of the entire assembly all move the number.
| Line item | Typical estimated range |
|---|---|
| Hinge, bracket or roller replacement | $150 – $350 |
| Latch, catch, and alignment repair | $150 – $400 |
| On-site weld repair (cracked frame, broken weld, brace) | $250 – $600 |
| Gate sag correction and re-hang | $350 – $900 |
| Slide gate track straightening or replacement | $400 – $1,100 |
| Weld repair plus front-end reinforcement on a steel leaf | $400 – $1,200 |
| Operator control board replacement | $300 – $800 installed |
| Operator motor or gearbox replacement | $450 – $900 installed |
| Loop detector or vehicle sensor replacement | $350 – $850 |
| Safety edge or photo-eye replacement | $200 – $500 |
| Intercom or keypad wiring and integration | $300 – $950 |
| Cantilever or slide leaf steel rebuild (heavy commercial) | $1,800 – $6,500 |
What pushes a job toward the top of these ranges is the weight of the leaf and how much of it has to come apart to weld it safely. A cracked weld on a lighter aluminum swing gate is a short visit. A bent steel cantilever leaf on a commercial property is a different job: the leaf comes off, the frame gets straightened and re-welded, the finish gets touched up, and the gate goes back on its track true. The automation side has its own price fork. A Mighty Mule control board is a modest part; a DoorKing board in a gated community with intercom and loop integration carries far more diagnostic and wiring time, simply because the system has more in it.
Brand matters here in a way it doesn’t in most trades. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule systems regularly, so the board, the motor, or the sensor in front of us isn’t a first-time puzzle. Get a gate specialist on-site, not a generalist guessing at your control board.
Safety note: gate operators run on line voltage and their control boards, loop wiring, and intercom low-voltage lines carry real risk, especially on older installations with unclear wiring. Heavy swing and slide leaves can crush if they drop off a track or a hinge fails. We always recommend a trained professional for anything involving the operator’s electrical side and for any work under a leaf that has to be lifted, braced, or re-hung.
What Affects Gate Parts & Welding Pricing in Bellevue
Part prices are set by the manufacturer. What moves a Bellevue job higher or lower is everything around the part. Here’s what we look at before we write a number.
- Gate weight and material. Aluminum, steel, wrought iron, and wood all behave differently under welding and re-hanging. A light aluminum leaf costs less to handle than a heavy steel cantilever leaf, and a wood gate blends structural repair with finish work.
- Brand and control architecture. A Mighty Mule residential operator is a straightforward parts swap. A DoorKing or LiftMaster commercial system with loop detectors, a keypad, an intercom, or a phone entry system can turn a 90-minute visit into a half-day, because every device on that chain has to be wired and tested together.
- Age of the system and parts availability. Older systems are where our brand range earns its keep. If a discontinued operator isn’t yours, we often have a compatible path with the same housing or a matching board from a brand we work on daily. That reduces or eliminates unnecessary replacement of a system we don’t recognize.
- Access. A gate on a steep Bellevue driveway, a tight alley, or inside a gated community HOA property takes longer to service. The Bellevue plateau and hillsides mean plenty of gates sit on slopes with tight approaches, and setting up safely around a slope costs time.
- Whether it’s one problem or three. A gate that’s dragging usually has a worn roller, a strained hinge, and a misaligned operator all at once. Fixing only one leaves the other two to wear the gate further. We diagnose all three on the same visit, so you pay one trip, not a chain of them.
- Whether the gate needs work above ground or below. Structural repairs at the leaf and hinge points are in the table above. Post and footing work, if a post has shifted, is a bigger job that we scope separately after we see it.
Bellevue’s mix of single-family hillside properties, multifamily buildings, and commercial and HOA gate entries means we quote all of these regularly – from a homeowner’s swing gate on a sloping drive to a DoorKing entry system at a commercial complex. If you’re not sure which category your gate falls into, start with a free on-site estimate.
How to Save on Gate Parts & Welding
Most of the savings on a gate repair come from fixing the right problem the first time. A cheap part swap that ignores a bent hinge or a worn track is the single most common reason we see repeat visits.
- Get it welded before it fails. A small weld crack caught early is a short repair. Left alone, it grows into a bent leaf and a re-hang. Small repairs are the cheapest line on our table.
- Have both sides looked at in one visit. When the operator is acting up, have the mechanical side inspected at the same time. Pairing a weld repair with a sensor or board replacement in one visit means one flat visit instead of two.
- Ask what’s replaced and what’s repaired. Some parts (rollers, hinges, boards) are replaced. Others (a leaf, a track, a post) can often be repaired, straightened, or reinforced. We walk you through which is which before we start, so you can see what you’re paying for.
- Check the brand and model on the operator. If you can read it, it saves diagnostic time. We know LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule systems, and knowing the model shortens the visit.
- Get a free estimate and a written price. Call (855) 683-9015 and we’ll schedule an on-site estimate at no charge. No fee for the estimate, no pricing surprises afterward.
We answer 24/7, and fast dispatch from 7am to 7pm, Sunday through Friday, gets a technician out to see the gate. If a gate fails on a Saturday, we’re closed that day – call and we’ll book you into the next opening, Sunday through Friday.
FAQs – Gate Parts & Welding Cost
How much does welding a gate cost in Bellevue?
On-site weld repair in Bellevue typically runs $250 to $600, and a weld plus reinforcement on a heavier leaf runs $400 to $1,200. The range depends on whether the weld is a simple crack fix or a structural rebuild that requires taking the leaf off the gate. A written estimate after an on-site look sets the final price. Call (855) 683-9015 for a free estimate.
Is it cheaper to repair my gate or replace it?
Repair is almost always cheaper unless the frame is structurally bent beyond straightening or the existing operator is obsolete and part of the gate’s structure. Most parts and welding repairs in Bellevue fall between $150 and $1,200, while a full replacement of a heavy gate leaf runs $1,800 to $6,500. We don’t recommend replacement unless repair genuinely won’t hold – our job is to diagnose the actual problem, not default to a new gate. Call (855) 683-9015 for an honest assessment.
How much does a new operator or control board cost in Bellevue?
A control board replacement typically costs $300 to $800 installed, and a motor or gearbox replacement runs $450 to $900. The system’s brand and its extra features – loop detectors, keypads, intercom integration – drive the top of that range because more devices have to be wired and tested. Call (855) 683-9015 and tell us the operator brand; it speeds up the estimate.
Can you repair a gate that’s sagging or off its track?
Yes. A sag correction and re-hang usually costs $350 to $900, and slide track straightening or replacement runs $400 to $1,100. A sagging gate is often a hinge, a weld, or a worn roller – all fixable without a full replacement. Call (855) 683-9015 to get a specialist on-site who can look at the whole assembly at once.
Do you work on my gate brand in Bellevue?
We work on nine major brands regularly: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, and we see them across residential, multifamily, and commercial properties in Bellevue. If your operator isn’t one of those, call anyway – our diagnostic approach is brand-agnostic, and we’ll find a path to the part. Call (855) 683-9015 to confirm your system before the visit.
When It’s Time for a Specialist
Gate parts and welding sit at the intersection of structural steel and low-voltage control, and most generalists only handle half of that. Whether your operator is a LiftMaster or a Mighty Mule, we carry the parts and know the system, and we work on everything from a single swing gate on a Bellevue hillside to a full commercial entry with DoorKing integration and loop detectors. That’s the whole point of what we do. Automated gate repair is its own specialty, and it’s all we do.
If your gate is dragging, straining, failing to close, or showing a cracked weld, call us. We offer free estimates, upfront pricing, and same-day service when the schedule allows. Call (855) 683-9015. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday, gets a specialist out to look at it, and the written estimate locks in your price before any work begins.
Want to explore more about how we help across the area? Start with Bellevue gate repair and the Bellevue service area page for the full picture of what a specialist can do for your gate.
Pricing reflects the Bellevue market as of 2026. Bellevue Gate Repair offers free estimates – call (855) 683-9015.
Written by the team at Bellevue Gate Repair.
What Our Customers Say
"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Allison Ziegler"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Jason Norris"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Paul Reed